|
|
|
|
|
|
Introducing Revolutionary QuartzLock: New Urethane Grout Technology
|
|
Technical Information and Usage Cautions
Showers/Steam Showers/Wet Applications
• Use an approved waterproof sealer for mud bed applications and follow manufacturer's recommendations for sealer installation. For liquid-applied waterproofing materials, apply to within 1" of any drains to prevent weep hole blockage. The use of pre-sloped, waterproof trays (instead of mud beds) is highly recommended.
• Shower, steam shower, pool, fountain and wet area installations must be protected from moisture and allowed to cure for 7 days before use.
• Do not apply or clean up this product like traditional cement-based or epoxy grouts; QuartzLock Grout is a new technology that requires a simpler and easier application and clean-up process.
• Follow all manufacturers' instructions for all other setting materials, waterproofing, anti-fracture membranes, etc. to be used on the job.
• Minimum recommended grout joint width is 1/16".
• Maximum recommended grout joint width is 1/2".
• Ensure that grout joints are fully packed, especially in tight and irregular joints. Take special care in all wet and outdoor applications.
• Do not use as a setting mortar.
• Not for use in heavy industrial applications (i.e. chemical plants), in areas subjected to harsh or persistent chemicals, or areas exposed to very aggressive cleaning routines such as steam or pressure washing.
• QuartzLock Grout is not a replacement for a waterproofing membrane. When a waterproofing system solution is required, please contact StarQuartz Technical Service.
• Protect grout from staining agents and chemicals during the cure process.
• Grouting when tile surface is above 90°F (32°C) is not recommended. Cool tile surface with damp sponge if tile surface is above 90°F (32°C). Be careful not to add excessive water during the tile cooling process.
• Do not use vinegar or acid solutions for clean-up; this could damage uncured grout.
• Always use protective clothing (gloves and eye protection) when working with grout.
• Prior to regrouting applications, remove 1/8" of old grout and any surface contaminants. Be sure to rinse any residual solvent/cleaner off grout joints, then allow joints to completely dry before re-grouting.
• Do not use for commercial or wet environment re-grouting installations, including showers, steam showers, and outdoor applications.
• Seal porous tile surfaces with a water-based sealer, including the sides of the stone, prior to grouting with QuartzLock Grout.
• Outdoor installations must be protected from moisture (rain) for 7 days. If rain is forecast within 7 days, protect by tenting the grouted area (at least 1 foot above surface).
• Not for use in hot tubs.
• Wait 7 days before rigorously cleaning tile and grout surface.
• Wait 7 days prior to exposing grout to full submersion.
• Use care on soft, highly polished surfaces to avoid scratching. Test a small area.
Use of a sealer is always recommended on polished marble, stone, slate and other natural, porous tiles.
• Use of enzymatic floor cleaners will void all warranties.
• Do not ingest. Keep out of the reach of children.
• Do not use StarCure® Urethane Grout Cure Accelerator.
• Do not use solvent-based adhesives or sealers with QuartzLock Grout.
• Protect grout from freezing. Do not grout outdoors or in unheated areas when temperatures are expected to be below 40°F (5°C) within 3 days. If product freezes, return to room temperature and use as directed.
• For Chemical Emergency, call CHEMTREC 24 hours, (800) 424-9300 in North America, (703) 527-3887 International (collect).
• For more information, consult the MSDS for this product.
|
TYPICAL PROPERTIES
|
WORKING PROPERTIES
|
| Water Cleanability |
Pass
|
Working Time |
3 hours
|
| Initial Set |
> 2 hours
|
Tack-Free Time |
8 hours
|
| Service Strength |
Pass
|
Ready for Light Foot Traffic |
24 hours
|
| Vertical Joint Sag |
Pass
|
Ready for Heavy Foot Traffic |
72 hours
|
| ASTM C267 Chemical |
Pass
|
Stain Resistant (food, etc) |
3 days
|
| Compressive Strength |
> 3,500 psi
|
Wet Area Installations |
7 Days
|
| Linear Shrinkage |
.06%
|
|
|
| Water Absorption |
< 1%
|
|
|
| Open Time |
180 minutes
|
|
|
| Color |
40 Available
|
|
|
|
|
Related Products and Information
|
|
|
|
|
 |
|
Benissimo Tile & Stone Care Products
|
|
Peel & Stick Surface Membrane |
|
Surface Art & the Environment
|
Clean, seal, and protect your tile and stone surfaces with Benissimo's complete line of Sealers, Cleaners, and Wipes.
|
|
If you have floor areas with problems like cracking or moisture, or where noise reduction is desired, use Surface Art's Peel & Stick Surface Membrane. Use under ceramic and stone tile, bamboo and hardwood floor.
|
|
HigLearn about the benefits of tile flooring as well as steps Surface Art is taking to reduce its impact on the environment.
|
| Learn More ►► |
|
|
|
|
.gif) |
|
|
|
|